How To Install A Door Lock And Handle
How to Install Front Door Hardware
Whether you're putting in a make-new door or merely replacing worn-out hardware, it's piece of cake to install a new handle and lock on your front end door.
Installing a front door handle and lockset is a quick and easy fashion to add curb appeal to your home. Before you lot begin, brand sure your door has standard preparation boreholes for a knob/lever and deadbolt combination.
This type of training means that the door has two sets of boreholes and cross bores, ane on elevation of the other, v-1/two inches from centre to center. Both boreholes should exist two-one/8 inches in diameter, with the cross bores measuring 1 inch in bore. The back set measures between 2-3/viii and ii-3/four inches from the edge of the door to the heart of the cantankerous bore. The thickness of the door should exist betwixt 1-3/viii and 1-3/4 inches. Exist enlightened of the dimensions of your new handle so that it fits properly on the door.
Apply caution when using an electric drill to install whatsoever screws. It could easily strip the spiral threads or impairment the hardware. Do not tighten to screws likewise tightly—you can always go back afterwards and tighten.
One time you've measured and prepped, you're ready to install a new door handle and lock. Follow our step-by-step instructions to get started.
How to Install a Door Handle and Lock
Supplies Needed
- Door knob/handle kit (we used the Addison handleset from Schlage)
- Deadbolt kit (if not included)
- Tape measure
- Pencil
- Utility knife, if needed
- 1-inch chisel, if needed
- Power drill (or Philips screwdriver with a long shaft)
- Countersink bit (if using a drill)
- Flathead screwdriver, optional
- Hammer
- Block of forest
Step-by-Footstep Directions
Follow our instructions for installing a front door handle and lockset to go a fresh look you lot dear and enhance your home'southward adjourn entreatment.
Step 1: Install the Latch
Make up one's mind whether you desire to use a flat, rectangular faceplate or a round drive-in faceplate. (Many kits come up with both options.) If y'all want to apply a flat faceplate but practise not have an indent on the edge of your door to fit information technology over the cross bore, trace the outline of the faceplate with a pencil and score the outline with a utility knife and so the wood doesn't splinter. Use a 1-inch chisel to chisel out a rectangle i/8-inch deep (it must be flush with the door jamb), one inch wide, and 2-i/four inches tall, centered effectually the cross bore. In one case yous have an indent on the edge of your door, slide the latch into the cross bore, with the bevel facing the door jamb, and secure it against the indent with two curt screws.
If you prefer the smaller round bulldoze-in faceplate, employ a flathead screwdriver to remove the screws on the apartment faceplate and support plate. Install the round drive-in faceplate over the latch and button down to secure. Slide the latch and drive-in faceplate into the cross diameter with the bevel facing the door jam, and push in until tight. Utilize a hammer with a block of wood between information technology and the latch to gently pound it into place (until flush with the edge of the door) without damaging the hardware.
Step 2: Install the Outside Handle
If your new door handle attaches to the door at a bespeak below the lower borehole (similar ours), you may need to drill another hole to accommodate. Line up the spindle on the back of the handle with the slot in the latch, sliding any mechanisms upwardly or down as needed to fit the handle onto the door.
Pace 3: Install the Inside Handle
Line up the inside handle or lever so that the spiral holes align vertically with the threaded posts on the back of the outside handle. If your inside handle is a lever, make sure that the lever is pointing away from the door jamb. Secure with screws. If your outside handle is attached to the door past a lower spindle (like ours), attach a washer, screw, and cover to secure and cease the spindle on the inside of the door.
Step four: Install the Deadbolt
Repeat the procedure above for creating a faceplate indent if your lock calls for 1 and your door does not already have i. Fit the latch bolt into the upper cantankerous diameter, making sure the top is facing upwardly (in that location is unremarkably an arrow on the latch bolt to point). Spiral the faceplate in to secure. Install the deadbolt mechanisms on the inside and exterior, making certain the keyed cylinder function is on the outside of the door. The inside thumb plow should signal upwardly when unlocked, and point towards the door jamb when locked.
Footstep 5: Install the Strike Plates
Marshal the strike plate for the handle against the door jamb and attach with two minor screws. Make sure the bent lip of the strike plate is facing the direction in which the door opens. Align the strike plate for the deadbolt, pre-drill your holes, and attach the strike plate to the door jamb with two longer screws for actress reinforcement. Alternate between the ii long screws every bit you drill them in so that the strike plate does not get pushed out of alignment.
Test the latch and the deadbolt to brand sure both slide in and out smoothly but not loosely. If the bolt won't plough all the fashion, drill the bolt pigsty a petty deeper until it does. Alternatively, you may need to adjust the position of the strike plate.
Source: https://www.bhg.com/home-improvement/door/exterior/how-to-install-front-door-hardware/
Posted by: linthoom1978.blogspot.com
0 Response to "How To Install A Door Lock And Handle"
Post a Comment